Basic knowledge about plumbing

n how they can protect your house or apartment before more flooding. Notification of such a failure of the hydraulic, which may require emergency hydraulic arrival is done by phone, and the arrival of such an emergency can occur w

Basic knowledge about plumbing emergency plumbers Islington

Hour Emergency Plumbing

Emergency hydraulic deals with the repair of sudden and serious failure of hydraulic. Employees pogotowania hydraulic also provide victims advice on how they can protect your house or apartment before more flooding. Notification of such a failure of the hydraulic, which may require emergency hydraulic arrival is done by phone, and the arrival of such an emergency can occur within several minutes. In the phone book you can find phone numbers for such branches emergency hydraulic, which are open around the clock and seven days a week, including holiday periods. But keep in mind that employees emergency hydraulic refuse to come to such repairs, which need not be performed immediately.


You can need it

The difference between pipes and tubes is simply in the way it is sized. PVC pipe for plumbing applications and galvanized steel pipe for instance, are measured in IPS (iron pipe size). Copper tube, CPVC, PeX and other tubing is measured nominally, which is basically an average diameter. These sizing schemes allow for universal adaptation of transitional fittings. For instance, 1/2" PeX tubing is the same size as 1/2" copper tubing. 1/2" PVC on the other hand is not the same size as 1/2" tubing, and therefore requires either a threaded male or female adapter to connect them. When used in agricultural irrigation, the singular form "pipe" is often used as a plural.7

Pipe is available in rigid "joints", which come in various lengths depending on the material. Tubing, in particular copper, comes in rigid hard tempered "joints" or soft tempered (annealed) rolls. PeX and CPVC tubing also comes in rigid "joints" or flexible rolls. The temper of the copper, that is whether it is a rigid "joint" or flexible roll, does not affect the sizing.7

The thicknesses of the water pipe and tube walls can vary. Pipe wall thickness is denoted by various schedules or for large bore polyethylene pipe in the UK by the Standard Dimension Ratio (SDR), defined as the ratio of the pipe diameter to its wall thickness. Pipe wall thickness increases with schedule, and is available in schedules 20, 40, 80, and higher in special cases. The schedule is largely determined by the operating pressure of the system, with higher pressures commanding greater thickness. Copper tubing is available in four wall thicknesses: type DWV (thinnest wall; only allowed as drain pipe per UPC), type 'M' (thin; typically only allowed as drain pipe by IPC code), type 'L' (thicker, standard duty for water lines and water service), and type 'K' (thickest, typically used underground between the main and the meter). Because piping and tubing are commodities, having a greater wall thickness implies higher initial cost. Thicker walled pipe generally implies greater durability and higher pressure tolerances.

Źródło: https://en.wikipedia.org/wiki/Water_pipe#Difference_between_pipes_and_tubes


Pipe type - elbow definition

An elbow is a pipe fitting installed between two lengths of pipe or tubing to allow a change of direction, usually a 90° or 45° angle, though 22.5° elbows are also made. The ends may be machined for butt welding, threaded (usually female), or socketed, etc. When the two ends differ in size, the fitting is called a reducing elbow or reducer elbow.

Elbows are categorized based on various design features as below:

Long Radius (LR) Elbows ? radius is 1.5 times the pipe diameter
Short Radius (SR) Elbows ? radius is 1.0 times the pipe diameter
90 Degree Elbow ? where change in direction required is 90°
60 Degree Elbow ? where change in direction required is 60°
45 Degree Elbow ? where change in direction required is 45°

A 90 degree elbow is also called a "90 bend" or "90 ell". It is a fitting which is bent in such a way to produce 90 degree change in the direction of flow in the pipe. It is used to change the direction in piping and is also sometimes called a "quarter bend". A 90 degree elbow attaches readily to plastic, copper, cast iron, steel and lead. It can also attach to rubber with stainless steel clamps. It is available in many materials like silicone, rubber compounds, galvanized steel, etc. The main application of an elbow (90 degree) is to connect hoses to valves, water pressure pumps, and deck drains. These elbows can be made from tough nylon material or NPT thread.

Źródło: https://en.wikipedia.org/wiki/Piping_and_plumbing_fitting